Your Position : home >Products > Patch Cord Production Line > Fiber Optic Epoxy Injection Machine

Products
Glue Injection Machine
< >
  • Glue Injection Machine
  • Glue Injection Machine

Glue Injection Machine

Application:
It's use for glue injection of connector
Characteristics:
1. Low cost
2. Use for less people production line
3. Easy operation

How to make the fiber patch cord production more efficiency, use the glue injection machine, click below to learn more

Specification

The way to spit
16 flexible setting way with time showing
Automatic timing spit
00.01 second~99.99 second
Manual timing spit
Can spit consistently
Minimum spit qty
0.0001 ml
Spit interval
0.1~9.9 second (Automatic timing function)
Input voltage 
220+/-10%,50hz
Internal voltage 
12VDC
Input air pressure
10-100pSi 
Output air pressure
1-80pSi
Dimension
235*225*63mm
Weight
<2.2kg
Spare parts instruction

Glue Injection Machine

1 Power: lighten-on, extinguish-off
2 Dispalyer for spit timing, showing time setting
3 Adjuster for input air pressure, pull out first, then air pressure up when clockwise switching, air 
pressure down when anti-clock switching
4
Air pressure displayer: 0~100pSi
5
Vacuum controler: Vacuum Withdrawing up when anti-clock switching, Vacuum Withdrawing down 
when clockwise switching
6 test button: it can replace the footswitch when testing
7 Spit time DIP button: show the time has set, using plus &subtract way 00.01second ~99.99 second
8 Interval DIP button: show the time has set, using plus &subtract way 0.1second ~9.9 second (timing 
automatically)
Spit outlet: connect spit needle
10 Air pressure input port: connect the high pressure air source
11 Programming unit for spiting way: 16 kinds flexible setting
12 Footswitch controller port: connect the footswitch switcher
13 Power input outlet
14 Insurance outlet
Instruction and installation

1. Installation

Glue Injection Machine

2. Setting the way

Glue Injection Machine

Attention and maintenance

1, Air pressure cant be more than 7bar(10psi), working air pressure cant be more than 5.5bar (78psi), if the working air pressurer is more than 4 bar, pls use the original parts from the manufacter.

 2, The liquid material must be stired evenly before putting to the cyliner needle. It will be better if the liquid material can be stored at the stable temperature of 5 degree centigrade to make sure there is no big change in the density of the liquid material. If the density of the liquid is so high, ( it means the liquid is so viscous, it may be hard to spit out). If the liquid need to be diluted, pls compliant to the instruction of the liquid material manufacture.

 3, Dont sharply increase the Vacuum, otherwise, the liquid will be pulled in the catheter by the vacuum. The qty of the vacuum pumpback rely on the air pressure level, working cycle, qty of the liquid to spit. If the qty of the vacuum is too much, the piston will be overset, disturbing the normal work.

 4, Avoid to overset the liquid cylinder, otherwise, the liquid will flow to the air cylinder to destroy the internal aprt.

 5, Pls clear the stuff left in the cylinder needel when needed. Otherwise the stuff will become hard, then disturbing the vacuum pumpback and stop the cylinder needle.

 6, After using the machine, the cylinder needle need to be cleaned every time, otherwise, it is difficult to unload the needle when the liquid becomes hard. Normally, it is easy to remove the liquid from the inside of the cylinder needle, just dipping the parts in the hand water for 5~10minutes, all the part will be cleaned.

 7, Pls disposal the used needle and cylinder needle at appropriate place to avoide some i nappropriate liquid pollution

TECHNOLOGY CO.,LTD
WIRENET TECHNOLOGY CO.,LTD
INTEGRITY WIN-WIN RESPECTS
Sincerely treat every customer,every colleague
Contact us
Add:Room 202, 2rd floor, 2 Building,Jingheyuan Industry Park,No.2004 Banxuegang Road, Bantian Street, Longgang District, Shenzhen, China
Tel:86-755-28461866
Fax:86-755-28461866
Cell:86-13603083476